Setup

From Tučňák Wiki
Revision as of 14:28, 20 June 2012 by Root (talk | contribs) (Alsa options)
Jump to: navigation, search
Setup menu

All configuration changes are in memory only until you save configuration.

Contest defaults

Contest defaults

There is possible to set these items in this menu: callsign in contest, club callsign (use only if you can export contest log in EDI format), locator (6 characters), contest QTH (is equal items PAdr1 and PAdr2 in EDI, Optional Exchange and standard proposed reports for SSB and CW.

Band defaults

Band defaults

This submenu contains setting of all bands. Active bands (QRV is checked) are separated from other bands. You can take away bands which are never used (as 220MHz in Europe).

You can enter single band setting by pressing ENTER key. Item `QRV on this band' is usually set for all bands where are permit transmittes.

This setting is the only one which must be set. Other items are better set here too but it isn't necessary.

QRV setting in this contest isn't effect on this place. Category can be one of Multi/Single/Check.

TX and RX Equip settings contains description of equipments. Power is written with units. ASL and AGL means a height between antenna and sea/ground. Inserted values are in meters, delimiter is semicolon.

Fill operator's callsigns into Operators field delimitely by semicolon. It is possible to fill it by Fill operators in menu Contest.

Remark field is assigned for remarks to contest commitee.

Single/Multi categories are categories valid (probably) only in Czech republic. They are used mostly for EDI files naming.

Band boundaries are entered in kilohertz. At this time they are used for DX-cluster spot filtration.

Adif band name is band description used in ADIF format.

QRG for skeds is initial frequency entered by operator to inform other operators about clean/CQ frequency on which they should take skeds. Format is not limited, you can use any string like ".120" etc.

Transverter's LO QRG is frequency which tucnak adds to frequency read from transceiver's CAT and result shows on the screen: f_\mathrm{display}=f_\mathrm{CAT} + f_\mathrm{lo} [Hz] Note some radios support transceiver mode for example radio is tuned on 14 MHz, CAT reports also 14 MHz but transceiver's display shows 144 MHz. LO frequency must be computed by operator, you can use Fix QRG in Edit menu.

This is local frequency for one band. Normally enter 0 to use Global LO frequency.

Band switch value is value sent to some keying devices to inform your contest hardware about active band in Tucnak.

Responsible operator

Responsible operator

There are set information of responsible operator for communication with contest commitee in this dialogue. All items are in free format and don't need commentary.

CW keying

CW daemon

Since version 2.0 Tucnak does not use the external program 'cwdaemon' for keying and transmitting CW. Its functions are included in Tucnak.

Keying methods are:

  • None - no CW output is used
  • lp - uses kernel module ppdev for keying. Recommended device is Dávač 3.3. Pin configuration is:
    • 1 STROBE - grounded when active.
    • 14 AUTOLF - switch TRX modulation input to microphone or soundcard output. Also indicate CW CQ to allow complex device to CQ on more bands simultaneously.
    • 16 INIT - PTT
    • 17 SELECT IN - CW
  • ttys - uses control pins of serial port. Pinout for D-SUB9:
    • 4 DTR - CW
    • 5 GND - ground
    • 7 RTS - PTT
  • davac4 - USB SSB/CW keyer Davac4 by OK1ZIA
  • cwdaemon - controls cwdaemon by Joop PG4I
  • winkey - uses Winkey by K1EL

Keying device f.e. /dev/parport0, /dev/ttyS0, /dev/ttyUSB0

Hostname, UDP port are reserved.

Initial speed says keying speed in WPM after program start. You can change it using PageUp or PageDown keys.

Weighting - changes ratio of mark and space in CW.

t_\mathrm{mark}=\frac{1\,200\,000}{\mathrm{speed}}+500 * \mathrm{weight}\ [\mu s]

t_\mathrm{space}=\frac{1\,200\,000}{\mathrm{speed}}-500 * \mathrm{weight}\ [\mu s]

WPM range describes the speed that can be set with PageUp/PageDown keys. Minimal WPM is also used for Winkey - it can handle only 31 speed steps. Normally minimal speed is set to 10 WPM which means winkey range 10-41 WPM. If you need for example 50 WPM, set minimal WPM to at least 19.

Use speaker - beeps using program soundwrapper.

PTT lead in - (experimental feature) Tucnak turns on PTT some time before CW to key on TRX and PA's to prevent "eating" of begin of code. It also allows the TX chain to stabilise before sending. Suggest 100 -> 250 ms.

Winkey options

Winkey options

Fast initialisation means that Tucnak doesn't wait for Winkey initialisation. It can be used mostly for winkey2 which is commonly supplied from USB. It has no effect for other version-depending commands (buttons), tucnak reads winkey version.

Use speed pot/use buttons - doesn't need comment. Normally is no reason to turn they off.

Curtis A/B, Ultimate, hand bug - set's paddle mode. I think optimal is Curtis B.

Paddle swap - also without comment :-)

Audio

Audio options

Since 2.0 Tucnak takes also SSB functionality for CQs and traffic recording.

Common options

Alsa, OSS, SSBD are supported "audio drivers".

Record traffic switches on/off recording band activity on receiving. If this option isn't active then all next options are irrelevant. To prevent consuming of all free space, use options Max. record duration and Minimal disk free space.

Record format option describe coding of output file. Supported options are.

  • PCM 8 and 16 bits
  • Logarithmic PCM u-law and A-law
  • IMA and MS adaptation PCM
  • GSM version 6.10 (preferred for me)

PCM coding is suitable for conversion to other formats (MP3, Ogg). GSM coding has low size. One minute of recording have size about 130 kB of disk space. That is less then 200 MB for 24 hours. This coding doesn't have to supported by your favourite player! GSM format replay for example mplayer (with codec) or sndfile-play distributed with libsndfile.

Option Channels sets number of sound channels. Set it to 1 (mono). You can set it to 2 or 4 it depends on your sound card capability.

Sample rate sets the number of sample per second. `CD' quality has value 44100. This value is needless for radio activity. It's recommended to lower value to half (22050) or quarter (11025) because some programs or sound cards can't work with other values.

Playback volume provides possibility to set playback volume for SSB CQ. Enter -1 to disable this feature. Common valid volumes are 0 to 100 but can be different if you use some special hardware with fancy cost-down.

Note in versions prior 2.26 is bug that doesn't allow to load negative value from rc file. As workaround you can try to enter invalid mixer device.

Capture volume the same for traffic recording.

Template for recorded filename is template for naming recording files. Description of possible macros you can find in section CQ macros.

Alsa options

Alsa playback device and Alsa capture device hold Alsa devices, plugs etc. Valid values are for example:

  • default - default device in your configuration
  • hw0,0 - first card, first PCM (first DAC)
  • hw0,1 - first card, second PCM (second DAC, f.e. Ensonic ES1371)
  • hw1,0 - second card ...
  • plughw0,0 - see Alsa documentation
  • dmix
  • pulse - recent versions of non-Debian linux use "PulseAudio" sound system. Tested [G1OGY](Playback ONLY) on Ubuntu 10.04LTS & Ubuntu 11.10.

Tip: run tucnak -i from terminal to see all detected Alsa soundcards

Period time is maximal amount of time for holding samples in card buffer for capture. Rasonable values are in hundreds (tenth of second).

Buffer time is maximal total size of buffer. Must be greater than Period time, f.e. 4*Buffer timer.

Alsa mixer device f.e. hw0, hw1, ...

Capture source button shows submnenu for capture. In menu are all detected sources on specified soundcard.

OSS options

OSS DSP describes path to special file which is connected with sound card kernel driver. Typically is /dev/dsp.

Max. num of fragments tells number of buffer fragment which can be holded in buffer. If you have problems with recording or witdh transition RX -> TX, try to set to 4 or similar small number. Then check recorded files for buffer underruns.

OSS mixer path to OSS mixer. typically /dev/mixer.

Record source - input for recording signal.

SSBD options

Currently unimplemented! SSBD is now obsolete. Settings is here for eventual future control of other software/devices (PowerSDR, digimodes...)

SSBD hostname and UDP port - set IP address and UDP port of ssb daemon.

Problems

  • Tucnak does not record band traffic
    1. Is Record traffic on?
    2. Is Max. record duration set enough value?
    3. Is Minimal disk free space set to higher than actual free space?
    4. Don't you use cwdaemon? In 2.33 the bi-directional communication is broken so Tucnak don't know when CW stops
    5. Isn't contest more than two days old? When is, tucnak thinks you only viewing old contest.

CW CQ

The list of all CW texts are showed after selecting this item. There is showed the key for running the message in brakes. Character `R' means that the message is repeated (CQ). Also is showing start of text.

CW CQ

There are these items in dialoque for setting CQ:

text of CQ. You can use plain text and macros

speed is normally undefined but you can define speed only for this CQ (f.e. for fast 73)

repeat CQ will be repeated until you press ESC, TAB or other CQ key

delay determines time between CQ messages

allow if... allows to run message if there is any macro undefined. Typically you don't want to give empty string if you have no callsign entered.

SSB CQ

SSB CQ

filename - file which is played as CQ. You can use macros f.e. /home/user/tucnak/cq/$MC_$O.wav to have multiple files for more callsign and more operators. Some audio output devices can have limitations to the audio format - samplerate, channels.

repeat and delay has same effect as in previous chapter

CQ macros

It's possible to define macros in texts of CW CQ and in name of SSB CQ file. Macros are case insensitive.

  • $$ - character $
  • $B - callsign of opposite station if differs from sent $C. Useful for "$B TU 73" in run mode. Does not work with Winkey and cwdaemon.
  • $C - callsign of opposite station. Warning! Callsign may contains stroke then can be problem to use macros in filename of CQ SSB. Look at $V
  • $D - date of contest (20031228)
  • $E - if contest code was entered during recording, string "code" will be added. Useful for post-contest record check, you can see important files by their filenames
  • $I - contents of inputline. Dots are replaced by question marks. Good idea is to follow $I by question mark in CQ definition.
  • $N - contest number from opposite station
  • $O - operator's callsign (for SSB CQ filenames)
  • $R - report from opposite station.
  • $S - serial number of record sample
  • $T - contest directory (/home/ok1zia/tucnak/20031004.2)
  • $V - callsign of opposite station, the stroke character is exchanged by the underline character
  • $W - locator of opposite station
  • $X - optional exchange from opposite station
  • $MC - my callsign
  • $MN - contest number to opposite station. For band or for all bands depening on Global QSO NR
  • $MR - report to opposite station
  • $MW - my locator
  • $MX - my optional exchange

You can also use case sensitive macros from strftime(3) for example:

  •  %d - day of month 01..31
  •  %H - hours 01..24
  •  %M - minutes 00..59
  •  %m - month 00..12
  •  %S - seconds 00-59
  •  %Y - year 1970-2038

For others use command:

man 3 strftime

Macros have no effect in all contexts.

Rig options

Tucnak uses hamlib for accessing rig (transceiver) via CAT interface. You can use probably any interface which is working with other programs. Good helper is HB9DRV's guide to HRD. Or you can build one of my RIG interfaces.

Rig options

Device device where the interface is connected. Typically /dev/ttyS0, /dev/ttyUSB0

Model model of rig. It is number defined by hamlib. You can obtain it by running command rigctl -l or you can use:

Choose Press button to show menu. In the first level you will choose manufacturer, in second level rig model. Model number is written to the previous field.

Baudrate communication speed. Leave 0 to use default hamlib value

CIV address address of rig if you have more Icom radios connected via one interface. Enter 0 for default address.

Freq. shift SSB->CW some old radios (Icom, Kenwood) shifts frequency when changing mode SSB <--> CW. If you call CQ on SSB and someone calls you in CW, you must switch to CW and tune for about 800Hz up. Tucnak can compensate this shift when you use Alt+M to switch mode.

Transverter's LO QRG is frequency which tucnak adds to frequency read from transceiver's CAT and result shows on the screen: f_\mathrm{display}=f_\mathrm{CAT} + f_\mathrm{lo} [Hz] Note some radios support transceiver mode for example radio is tuned on 14 MHz, CAT reports also 14 MHz but transceiver's display shows 144 MHz. LO frequency must be computed by operator, you can use Fix QRG in Edit menu. This is global LO freq, if you use more transceivers, you can set more frequencies in Band defaults menu.

Rig poll interval set if communication with radio produces system load

Set band from radio log's band is switched automatically when radio is tuned to other band

Change band on radio radio's band is changed when operator switches band in log

Change mode on radio radio's mode is changed when operator changes mode

Clear RIT on RUN's QSO save in Run mode clear RIT after QSO is stored. Depends on radio/hamlib capabilities.

Rotar options

Tucnak supports many antenna rotators (called rotars in tucnak). Some designed by OK1ZIA and many supported by hamlib. You can use more rotators at time so when you choose Rotar options menu item, next menu will appear:

Rotator choose


Add rotator

Show rotator option:

Rotator options
  • Description is text for operator which describes rotator device.
    • None rotator is disabled
    • OK1ZIA ttys OK1ZIA's rotator connected by serial port
    • OK1ZIA FTDI OK1ZIA's rotator connected by FT232RL device using USB bus
    • Hamlib rotator is accessed using hamlib
    • Remote rotator is physically connected to other Tucnak over network
  • Filename COM port where is rotator connected (/dev/ttyS0, /dev/ttyUSB0 or COM1). Also hostname for network-controlled hamlib rotators
  • Hostname IP address (network identification obtained in Network info for Remote rotator type
  • UDP port TCP (yes) port for remote rotator type, normally 55555
  • VID USB Vendor ID for FTDI rotator type
  • PID USB Product ID for FTDI rotator type
  • Serial # Serial number for FTDI rotator type if you need to distinguish between two devices with same VID:PID. Can be empty.
  • Timeout Time to wait for device reply
  • Poll interval Delay between QTF queries
  • Beam width value for map to show relevant antenna width. Used also for gain chart.
  • Communication address for OK1ZIA's rotator. Address allows to distinguish more rotators connected via one FTDI converter. Default value is 240, variant with 2x azimuth have 240 and 241 for second system.
  • Model hamlib model number of rotator
  • Rotator letter for remote letter which has remote rotator on remote side

Remove rotator

Remove rotator

Choose one rotator to remove from Tucnak's configuration.

Autosave

Autosave options

It sets and saves parameters of QSO to disk. Option Save to disk after QSO is recommended set to 1 to save all reports. Fsync option immediately saves QSOs from cache to disk.

Default setting of option Save to disk after QSO is 4. Zero disables saving to floppy disk. Path to floppy item sets path to floppy's mount point. Tucnak doesn't test if floppy disk is mounted or not.

Other items are ignored.

Network & trace

Network & trace options

Ignore interfaces - list of network interfaces which would be ignored when searching for more instances of Tucnak on the network (transmit broadcasts) as connect to Internet, public IP address from provider, AX.25 interface. The delimiter between interfaces is space character. Broadcasts loads slow nets.

Ignore networks - the purpose this option is the same as Ignore interface option. You can determinate subnet address.

Announce to nets - it's an inverse function of previous options. There is specification of IP address where have been sending broadcasts in this option. The routers usually have disabled forward broadcastings.

Miscellaneous options

Miscellaneous options

Font height for very-high-resolution displays and bad eyes - fonts are resized from usual 9x16. Usable are values 16 (old font), 24 (new alternative in 3.00) and 32 (doublesized 16). Other values are not very usable because resize algorithm is trivial but at IARU VHF 2008 I had nothing to do so I've imlpemented it.

Screen resolution Only for SDL mode - you can set resolution of tucnak's window in characters or in pixels

Starting band Band character (f.e. C=144 MHz) of band, which will be activated after contest open.

Log lines are last lines of tucnak's screen on which tucnak writes informations for users.

Sked shift time added to current time filled in the Sked dialog. Obsoloted and removed in 3.01

Sked count in popup - number of lines displayed in sked notification window

Slash key Slash key on some national keyboards is not easily accessible (only with shift). Here you can remap it to any other character. Use with care!

Disable screensaver if you only test Tucnak at home, you probably don't want to disable screensaver. So turn these checkbox off. Works only under X11 (Linux).

Terminal options

Terminal options

These options come from links browser so I'm not able to tell what they exactly mean. Try to make some experiments or look at source code :-)

Language

Set language of Tucnak's GUI. I think English is very good for contest log but some people like to have their mother tongue set.

Character set

This menu is used for setting characteristic of terminal as window frames. It's a legacy of links (as above), I don't have detailed knowledge about these options.

Load cfg from net

It shows addresses of all Tucnaks on the local network. If one is selected you will read his complete configuration (tucnakrc).

Load C_W from net

It loads complete C_W database from selected Tucnak and saves it to ~/tucnak/tucnakcw. In database are saved two newest locators for each callsign.

Save configuration

It saves current configuration to file ~/tucnak/tucnakrc . You MUST do it to preserve any configuration changes !!